Hyundai i-30: Windshield Glass / Tail Gate Window Glass
Components and components location
Repair procedures
| •
|
Put on gloves to prevent hand injuries.
|
|
| •
|
Use seat covers to avoid damaging any surfaces.
|
|
|
1. |
Remove the tailgate trim.
(Refer to Tailgate - "Tailgate Trim")
|
|
2. |
Disconnect the hot wire connector (A).
|
|
3. |
Cut off the sealant on the edge (B) while pulling the piano wire (A)
to the left and right.
|
• |
Put on gloves to protect your hands.
|
|
• |
Heat may occur when working on the wires. Be careful
not to burn your hands.
|
|
• |
Be careful not to disconnect the piano wire.
|
|
|
|
4. |
Put in a piano wire (A) through the corner of the tailgate window glass
and insert wire grips into both ends of the wire.
|
|
5. |
Cut off the sealant on (A-A), (B-B), (C-C), while pulling a piano wire
(A) to the left and right.
|
• |
Put on gloves to protect your hands.
|
|
• |
Heat may occur when working on the wires. Be careful
not to burn your hands.
|
|
• |
Be careful not to disconnect the piano wire.
|
|
|
|
6. |
Remove the tailgate window glass (A).
|
|
1. |
Using a cutting knife (A), remove the remaining sealant (B) on the body
panel.
|
• |
Put on gloves to protect your hands.
|
|
|
|
2. |
Apply the body primer to the bonding surface of body panel.
|
• |
Be careful not to touch the surface covered with the
primer because touching it may lead to water leaks after
installing the tailgate window glass.
|
|
• |
Do not apply the body primer to the glass.
|
|
• |
Remove any foreign materials from the primer-covered
surface.
|
|
|
|
3. |
Apply the glass primer to the outer edge of tailgate window glass.
|
• |
Be careful not to touch the surface covered with the
primer because touching it may lead to water leaks after
installing the tailgate window glass.
|
|
• |
Remove any foreign materials from the primer-covered
surface.
|
|
|
|
4. |
Using a sealant gun, apply the sealant (B) to the edge of rear tailgate
window glass (A).
|
|
5. |
Using the glass holder, adjust the tailgate window glass (A) to fit
the alignment marks (B) on the body and lightly push the tailgate window
glass to make the edges fully seated on the bonding surface of body.
|
• |
When installing the tailgate window glass (B), be sure
to fit the protruding part (C) on the reverse side of
the glass into the groove on the body frame.
|
|
|
|
6. |
To make sure that the applied sealant is completely hardened, leave
the car on a flat surface for at least 3 to 4 hours after installing
the tailgate window glass.
|
• |
If driving the car is inevitable, drive at a low speed
for at least 8 hours.
|
|
• |
Advise the driver to avoid aggressive driving or driving
on rough roads for 2-3 days after installing the tailgate
window glass.
|
|
|
|
7. |
Conduct a leak testing.
|
• |
The leak testing shall be conducted at least 4 hours
after the tailgate window glass installation is completed.
|
|
• |
Do not directly spray the high-pressure water to the
joint area.
|
|
|
|
8. |
Install the tailgate trim.
(Refer to Tailgate - "Tailgate Trim")
|
Replacement
[Removal]
•
Put on gloves to prevent hand injuries...
Other information:
Description
Idle Stop & Go (ISG) system switches off the ignition when vehicle is stopped,
and then restarts the ignition and starts the vehicle when accelerator is pushed.
It temporarily stops the engine while waiting for signal or idling to improve
fuel efficiency and reduce exhaust gas emission...
Description and operation
Description
Rail Pressure Sensor (RPS) is installed on the delivery pipe and measures the
instantaneous fuel pressure in the delivery pipe. The sensing element (Semiconductor
element) built in the sensor converts the pressure to voltage signal...
Categories
(1) Driver’s door power window
switch
(2) Front passenger’s door power
window switch
(3) Rear door (right) power window
switch
(4) Rear door (left) power window
switch
(5) Window opening and closing
(6) Automatic power window
(7) Power window lock switch
read more
Repair procedures
Floor Carpet