Hyundai i-30: ESP (Electronic Stability Program) System / Troubleshooting

Hyundai i30 (PD) 2018-2024 Service Manual / Brake System / ESP (Electronic Stability Program) System / Troubleshooting

Failure Diagnosis
1.
In principle, ESP and TCS controls are prohibited in case of ABS failure.
2.
When ESP or TCS fails, only the failed system control is prohibited.
3.
However, when the solenoid valve relay should be turned off in case of ESP failure, refer to the ABS fail-safe.
4.
Information on ABS fail-safe is identical to the fail-safe in systems where ESP is not installed.
Memory of Fail Code
1.
It keeps the code as far as the backup lamp power is connected. (O)
2.
It keeps the code as long as the HCU power is on. (X)
Failure Checkup
1.
Initial checkup is performed immediately after the HECU power on.
2.
Valve relay checkup is performed immediately after the IG2 ON.
3.
It executes the checkup all the time while the IG2 power is on.
4.
Initial checkup is made in the following cases.
(1)
When no failure is detected
(2)
When ABS and ESP are not in control.
(3)
Initial checkup is not made after ECU power on.
(4)
If the vehicle speed is over 5 mph(8 km/h) when the brake lamp switch is off.
(5)
When the vehicle speed is over 24.8 mph(40 km/h).
5.
Though, it keeps on checkup even if the brake lamp switch is on.
6.
When performing ABS or ESP control before the initial checkup, stop the initial checkup and wait for the HECU power input again.
7.
Judge failure in the following cases.
(1)
When the power is normal.
(2)
From the point in which the vehicle speed reaches 4.9 mph(8 km/h) after HECU power on.
Countermeasures In Fail
1.
Shut the system down and perform the following actions and wait for HECU power OFF.
2.
Turn the valve relay off.
3.
Do not perform any ABS/TCS/ESP functions until normal operating condition is restored.
Warning Lamp ON
1.
ABS warning lamp turns on when ABS is malfunctioning.
2.
ESP function/ warning lamp turns on when ESP is malfunctioning.
When power voltage and valve relay voltage are abnormal, input/output related failure judgment is not made.

    Repair procedures

    Inspection ESP System Bleeding This procedure should be followed to ensure adequate bleeding of air and filling of the ESC unit, brake lines and master cylinder with brake fluid...

    ESP Control Unit

    Components and components location Components [LHD] 1. Front - right tube 2. Rear - left tube 3. Rear - right tube 4...

    Other information:

    Hyundai i30 (PD) 2018-2024 Owner's Manual: Fan speed control


    Turn the knob to the right to increase the fan speed and airflow. Turn the knob to the left to decrease fan speed and airflow. Setting the fan speed control knob to the “0” position turns off the fan. NOTICE Operating the fan speed when the ignition switch is in the ON position could cause the battery to discharge...

    Hyundai i30 (PD) 2018-2024 Service Manual: Specifications


    Specifications Front Suspension Item Specification Suspension type Mac Pherson Strut Shock absorber Type Conventional valve Rear Suspension Item Specification Suspension type Multi link Shock absorber Type Conventional valve Wheel & Tire Item Specification Normal load Maximum load Front Rear Front Rear Wheel Aluminum 6...

    Categories

    Panorama sunroof

    If your vehicle is equipped with a sunroof, you can slide or tilt your sunroof with the sunroof control lever located on the overhead console.

    Hyundai i30. Panorama sunroof

    The ignition switch must be in the ON position before you can open or close the sunroof.

    The sunroof can be operated for approximately 30 seconds after the ignition key is removed or turned to the ACC or LOCK(or OFF) position. However, if the front door is opened, the sunroof cannot be operated even within 30 seconds.

    read more


     
    Copyright © 2024 www.hi30.net