Hyundai i-30: Smart key / Smart key precautions
The smart key may not work if any of
the following occur:
- The smart key is close to a radio
transmitter such as a radio station
or an airport which can interfere
with normal operation of the smart
key.
- The smart key is near a mobile two
way radio system or a mobile
phone.
- Another vehicle’s smart key is
being operated close to your vehicle.
If the smart key does not work correctly,
open and close the door with
the mechanical key. If you have a
problem with the smart key, it is recommended
that you contact a
HYUNDAI authorised repairer.
If the smart key is in close proximity
to your mobile phone, the signal
could be blocked by your mobile
phone's normal operational signals.
This is specifically relevant when the
phone is active such as making and
receiving calls, text messaging,
and/or sending/receiving emails.
Avoid placing the smart key and your
mobile phone in the same location
and always try to maintain an adequate
distance between the two
devices.
Information
Changes or modifications not expressly
approved by the party responsible
for compliance could void the user’s
authority to operate the equipment. If
the keyless entry system is inoperative
due to changes or modifications not
expressly approved by the party
responsible for compliance, it will not
be covered by your manufacturer’s
vehicle warranty.
NOTICE
Keep the smart key away from
electromagnetic materials that
blocks electromagnetic waves to
the key surface.
NOTICE
Always have the smart key with
you when leaving the vehicle. If
the smart key is left near the vehicle,
the vehicle battery may be discharged.
If the Smart Key does not operate
normally, you can lock or unlock the
door by using the mechanical key.
Move the release lever in the direction
of the arrow (1) and then remove
the mechanical key (2)...
If the Smart Key is not working properly,
try replacing the battery with a
new one.
Battery Type: CR2032
To replace the battery:
1. Remove the mechanical key...
Other information:
Components and components location
Components
No
Connector A
Connector B
Connector C
1
-
IGN 2 Relay output
Battery signal
2
SSB Switch 1 input
C CAN (Low)
-
3
Driver door antenna switch input
C CAN (High)
Immoblizer antenna power
4
-
B CAN (High)
Driver out side handle antenna power
5
-
B CAN (Low)
Assist out side handle antenna power
6
-
SSB Illumination (orange)
Bumper antenna power
7
RPM Input
-
Interior antenna 1 power
8
Start signal feedback input
SSB Illumination (+) output
Interior antenna 2 power
9
clutch switch input
ESCL enable output
Interior antenna 3 power
10
-
Battery power
-
11
Starter relay output
IGN 1 Relay output
-
12
Power 1
ESCL COM
-
13
SSB Switch 2 input
EMS COM
ESCL (-) output
14
Assist door antenna switch input
-
Immoblizer antenna ground
15
-
SSB Illumination (-) output
Driver out side handle antenna ground
16
Clutch switch input
SSB LED Output
Assist out side handle antenna ground
17
ESCL unlock swtich input
SSB LED IGN Output
Bumper antenna ground
18
Wheel speed sensor input
External buzzer
Interior antenna 1 ground
19
ACC Input
-
Interior antenna 2 ground
20
IGN 1
ESCL (+) output
Interior antenna 3 ground
21
Brake switch input
-
22
ACC Relay input
GND Power 2
Schematic diagrams
Circuit Diagram
Repair procedures
Removal
Smart Key Unit
1...
Specifications
Item
Specification
Type
Electric Power Steering System
Steering gear
Type
Rack & Pinion
Rack stroke
154 ± 1 mm (6...
Categories
To signal a turn, push down on the
lever for a left turn or up for a right
turn in position (A). To signal a lane
change, move the turn signal lever
slightly and hold it in position (B).The
lever will return to the OFF position
when released or when the turn is
completed.
read more