Hyundai i-30: Suspension System (NON-ECS) / Troubleshooting
Symptom
|
Possible cause
|
Remedy
|
Hard steering
|
Improper front wheel alignment
Excessive turning resistance of lower arm ball joint
Low tire pressure
No power assist
|
Correct
Replace
Adjust
Repair and replace
|
Poor return of steering wheel to center
|
Improper front wheel alignment
|
Correct
|
Poor or rough ride
|
Improper front wheel alignment
Malfunctioning shock absorber
Broken or worn stabilizer
Broken or worn coil spring
Worn lower arm bushing
|
Correct
Repair or replace
Replace
Replace
Replace the lower arm assembly
|
Abnormal tire wear
|
Improper front wheel alignment
Improper tire pressure
Malfunctioning shock absorber
|
Correct
Adjust or replace
Replace
|
Wandering
|
Improper front wheel alignment
Poor turning resistance of lower arm ball joint
Loose or worn lower arm bushing
|
Correct
Repair
Retighten or replace
|
Vehicle pulls to one side
|
Improper front wheel alignment
Excessive turning resistance of lower arm ball joint
Broken or worn coil spring
Bent lower arm
|
Correct
Replace
Replace
Repair
|
Steering wheel shimmy
|
Improper front wheel alignment
Poor turning resistance of lower arm ball joint
Broken or worn stabilizer
Worn lower arm bushing
Malfunctioning shock absorber
Broken or worn coil spring
|
Correct
Replace
Replace
Replace
Replace
Replace
|
Bottoming
|
Broken or worn coil spring
Malfunctioning shock absorber
|
Replace
Replace
|
Wheel /tire noise, vibration and harshness concerns are directly related to
vehicle speed and are not generally affected by acceleration, coasting or decelerating.
Also, out-of-balance wheel and tires can vibrate at more than one speed. A vibration
that is affected by the engine rpm, or is eliminated by placing the transmission
in Neutral is not related to the tire and wheel. As a general rule, tire and
wheel vibrations felt in the steering wheel are related to the front tire and
wheel assemblies. Vibrations felt in the seat or floor are related to the rear
tire and wheel assemblies. This can initially isolate a concern to the front
or rear.
Careful attention must be paid to the tire and wheels. There are several symptoms
that can be caused by damaged or worn tire and wheels. Perform a careful visual
inspection of the tires and wheel assemblies. Spin the tires slowly and watch
for signs of lateral or radial runout. Refer to the tire wear chart to determine
the tire wear conditions and actions
Wheel and tire diagnosis
|
Rapid wear at the center
|
Rapid wear at both shoulders
|
Wear at one shoulder
|
|
|
|
•
|
Center-tread down to fabric due to excessive over inflated tires
|
•
|
Excessive toe on drive wheels
|
•
|
Heavy acceleration on drive
|
|
•
|
Worn suspension components
|
•
|
Excessive cornering speeds
|
|
•
|
Toe adjustment out of specification
|
•
|
Camber out of specification
|
|
Partial wear
|
Feathered edge
|
Wear pattern
|
|
|
|
•
|
Caused by irregular burrs on brake drums
|
|
•
|
Toe adjustment out of specification
|
•
|
Damaged or worn tie rods
|
|
•
|
Excessive toe on non-drive wheels
|
|
Special Service Tools
Tool (Number and Name)
Illustration
Use
09568-1S100
Saperate the ball joint from the front alxe
09546-3X100
Shock absorber lock nut removal tool
Used for remove the shock absorber lock nut...
Other information:
Components and components location
Component
Repair procedures
Removal
1.
Disconnect the negative(-) battery terminal.
2.
Remove the crash pad side ganish (RH).
(Refer to Body - "Glove Box Upper Cover Assembly" )
3...
Components and components location
Components
No
Connector A
Connector B
Connector C
1
-
IGN 2 Relay output
Battery signal
2
SSB Switch 1 input
C CAN (Low)
-
3
Driver door antenna switch input
C CAN (High)
Immoblizer antenna power
4
-
B CAN (High)
Driver out side handle antenna power
5
-
B CAN (Low)
Assist out side handle antenna power
6
-
SSB Illumination (orange)
Bumper antenna power
7
RPM Input
-
Interior antenna 1 power
8
Start signal feedback input
SSB Illumination (+) output
Interior antenna 2 power
9
clutch switch input
ESCL enable output
Interior antenna 3 power
10
-
Battery power
-
11
Starter relay output
IGN 1 Relay output
-
12
Power 1
ESCL COM
-
13
SSB Switch 2 input
EMS COM
ESCL (-) output
14
Assist door antenna switch input
-
Immoblizer antenna ground
15
-
SSB Illumination (-) output
Driver out side handle antenna ground
16
Clutch switch input
SSB LED Output
Assist out side handle antenna ground
17
ESCL unlock swtich input
SSB LED IGN Output
Bumper antenna ground
18
Wheel speed sensor input
External buzzer
Interior antenna 1 ground
19
ACC Input
-
Interior antenna 2 ground
20
IGN 1
ESCL (+) output
Interior antenna 3 ground
21
Brake switch input
-
22
ACC Relay input
GND Power 2
Schematic diagrams
Circuit Diagram
Repair procedures
Removal
Smart Key Unit
1...
Categories
When the High Beam Assist (HBA)
System is not working properly, the
warning message will come on for a
few second. After the message disappears,
the master warning light ()
will illuminate.
read more