Hyundai i-30: Tyre pressure monitoring system (TPMS)
(Type A) / TPMS (Tyre Pressure
Monitoring System)
malfunction indicator

The TPMS malfunction indicator will
illuminate after it blinks for approximately
one minute when there is a
problem with the Tyre Pressure
Monitoring System.
We recommend that the system be
checked by a HYUNDAI authorised
repairer.
NOTICE
If there is a malfunction with the
TPMS, the low tyre pressure position
telltale will not be displayed
even though the vehicle has an
under-inflated tyre.
CAUTION
- The TPMS malfunction indicator
may blink for approximately
1 minute and then remain continuously
illuminated if the
vehicle is moving around electric
power supply cables or
radios transmitter such as at
police stations, government
and public offices, broadcasting
stations, military installations,
airports, or transmitting
towers, etc. This can interfere
with normal operation of the
Tyre Pressure Monitoring
System (TPMS).
- The TPMS malfunction indicator
may blink for approximately
1 minute and then remain
continuously illuminated if
snow chains are used or
some separate electronic
devices such as notebook
computer, mobile charger,
remote starter or navigation
etc., are used in the vehicle.
This can interfere with normal
operation of the Tyre Pressure
Monitoring System (TPMS).
Low tyre pressure
telltale
Low tyre pressure
position telltale
and tyre pressure
telltale
When the tyre pressure monitoring
system warning indicators are illuminated
and a warning message displayed
on the cluster LCD display,
one or more of your tyres is significantly
under-inflated...
If you have a flat tyre, the low Tyre
Pressure and Position telltales will
come on. We recommend that the
system be checked by a HYUNDAI
authorised repairer...
Other information:
Components and components location
Components
Connector [A]
Pin NO
Function
Pin NO
Function
1
Battery (+)
21
IGN2
2
ISG B+
22
IGN1
3
ILL+ (TAIL)
23
Blower motor (+)
4
Sensor REF (+5V)
24
Photo sensor_LH
5
Mode actuator feedback
25
Photo sensor_RH
6
Temperature actuator feedback
26
-
7
Intake actuator feedback
27
-
8
EVAP Sensor (+)
28
PTC Relay 3
9
AMB Sensor (+)
29
PTC Relay 2
10
Mode actuator (Vent)
30
PTC on signal
11
Mode actuator (Defrost)
31
Detent OUT (-)
12
Temperature actuator (Cool)
32
-
13
Temperature actuator (Warm)
33
C_CAN High
14
Intake actuator (Fresh Air)
34
C_CAN Low
15
Intake actuator (Recirculated Air)
35
Power mosfet (Drain feed back)
16
HTD (Rear defog indicator)
36
Power mosfet (Gate)
17
Rear defog switch
37
ECV +
18
Clean signal
38
ECV- (Ground)
19
Ionizer diagnosis
39
Sensor ground
20
ILL- (RHEO)
40
Ground
Connector [B]
Pin NO
Function
Pin NO
Function
1
Passenger's temperature control actuator (Feedback)
9
-
2
Passenger's temperature control actuator (Cool)
10
Duct sensor (+)_Vent
3
Passenger's temperature control actuator (Warm)
11
Duct sensor (-)_Floor
4
Auto defogging (Feedback)
12
Auto defogging sensor signal
5
Auto defogging (Open)
13
-
6
Auto defogging (Off)
14
-
7
-
15
-
8
-
16
Ground
Repair procedures
Self Diagnosis
1...
Components and components location
Component Location
1. Main crash
pad assembly
Repair procedures
Replacement
•
Put on gloves to prevent hand injuries...
Categories

When the High Beam Assist (HBA)
System is not working properly, the
warning message will come on for a
few second. After the message disappears,
the master warning light (
)
will illuminate.
read more